MuntsOS Embedded Linux Extra Device Tree Overlays Here are some collected device tree overlays for Raspberry Pi boards that have been written from scratch or customized from the kernel source distribution for MuntsOS. For I²C devices, the easiest way to determine the correct slave address is to run i2cdetect -y 1 before and after attaching the device and see what changes. Then you can add the proper dtoverlay command to /boot/config.txt AD5593R Analog/Digital I/O Expander dtoverlay=AD5593R dtparam=mode0=1 dtparam=mode1=1 dtparam=mode2=1 dtparam=mode3=1 dtparam=mode4=1 dtparam=mode5=1 dtparam=mode6=1 dtparam=mode7=1 dtparam=offstate0=0 dtparam=offstate1=0 dtparam=offstate2=0 dtparam=offstate3=0 dtparam=offstate4=0 dtparam=offstate5=0 dtparam=offstate6=0 dtparam=offstate7=0 Mode Values 0 Unused 1 ADC 2 DAC 3 ADC and DAC 8 GPIO Off State Values 0 Pulldown resistor 1 Output low (sinking) 2 Output high (sourcing) 3 Tri-State (high impedance) ADC121C021 Analog to Digital Converter dtoverlay=ADC121C021 dtparam=addr=0xNN dtparam=min=VVVVVVV dtparam=max=VVVVVVV The I²C slave address may be 0x50 (default if not specified), 0x51, 0x52, 0x54, 0x55, 0x56, 0x58, 0x59, or 0x5A. For the Grove I²C ADC module, the default address is 0x50 and the values for min and max should be 6000000 or 2 times the measured voltage, in microvolts, at pad VA. ADS1015 Analog to Digital Converter dtoverlay=ADS1015 dtparam=addr=0xNN dtparam=cha_enable dtparam=chb_enable dtparam=chc_enable dtparam=chd_enable dtparam=cha_cfg=4 dtparam=chb_cfg=5 dtparam=chc_cfg=6 dtparam=chd_cfg=7 dtparam=cha_gain=0 dtparam=chb_gain=0 dtparam=chc_gain=0 dtparam=chd_gain=0 The I²C slave address may be 0x48 (default if not specified) or 0x49. ENC28J60 Ethernet Adapter dtoverlay=ENC28J60 dtparam=cs=N dtparam=irq=N The value for the SPI slave select parameter cs is 0 for spidev0.0 or 1 for spidev0.1. Default is 0. The value for GPIO interrupt signal parameter irq must be a GPIO number. Default is 25. The default values are correct for the GeeekPi EN28J60 HAT so both dtparam lines may be omitted. Other ENC28J60 boards such as the Mikroelektronika ETH Click will likely require cs or irq or both. MCP23017 GPIO Expander dtoverlay=MCP23017 dtparam=addr=0xNN dtparam=gpiopin=N The I²C slave address may be 0x20 (default if not specified) to 0x27. MCP3428 Analog to Digital Converter dtoverlay=MCP3428 dtparam=addr=0xNN The I²C slave address may be 0x68 (default if not specified) to 0x6F. MUNTS-0018 Raspberry Pi Tutorial I/O Board dtoverlay=MUNTS-0018 dtparam=min=VVVVVVV dtparam=max=VVVVVVV You can improve the accuracy of the on-board MCP3204 ADC by setting min and max to the measured voltage, in microvolts, of the 3v3 power rail. PCA8574 GPIO Expander dtoverlay=PCA8574 dtparam=addr=0xNN The I²C slave address may be 0x20 (default if not specified) to 0x27 (PCA8574, PCF8574) or 0x38 to 0x3F (PCA8574A, PCF8574A). PCA9685 PWM Expander dtoverlay=PCA9685 dtparam=addr=0xNN Possible I²C slave addresses range from 0x40 (default if not specified) to 0x7F, though some of these will conflict with other devices and reserved addresses. 0x40 and 0x70 are common. This overlay does not support GPIO mode. Pi 3 Click Shield dtoverlay=Pi3ClickShield Pi 4 Click Shield dtoverlay=Pi4ClickShield W5500 Ethernet Adapter dtoverlay=W5500 dtparam=cs=N dtparam=irq=N The value for the SPI slave select parameter cs is 0 for spidev0.0 or 1 for spidev0.1. Default is 0. The value for GPIO interrupt signal parameter irq must be a GPIO number. Default is 25. ------------------------------------------------------------------------ Questions or comments to Philip Munts phil@munts.net